User not logged in - login - register
Home Calendar Books School Tool Photo Gallery Message Boards Users Statistics Advertise Site Info
go to bottom | |
 Message Boards » » Speaker question Page [1]  
sundance
All American
1001 Posts
user info
edit post

I have a home theater receiver that outputs at 8-ohms but I have 6-ohm speakers. Is this going to pose any problems in the short term till I can afford 8-ohm speakers?

10/15/2005 12:24:45 AM

stopdropnrol
All American
3908 Posts
user info
edit post

running ur avr 235 at 6 ohms would probaly be ok for a short while considering thre's still 2 channels going ununsed and it's pretty quality peice of electronics. but i really would recomend against using them for a long time the 6 ohms speakers will cause the receiver to get hotter than normal with the lower impedance and possibly even shut off. if u got the $$ i'd sell that 5.1 setup. the tss450 works really well with the avr235 , if i can't sell it i plan to keep it and eventually get a pair of floor standing speakers to complete the 7.1.

10/15/2005 12:47:48 AM

darkone
(\/) (;,,,;) (\/)
11611 Posts
user info
edit post

Read the manual for the reciever. Most manuals will address this very issue.

10/15/2005 2:08:52 AM

esgargs
Suspended
97470 Posts
user info
edit post

lower resistance means more current

means hotter amp.

10/15/2005 2:42:15 AM

sundance
All American
1001 Posts
user info
edit post

ok now its reversed. 6-ohm receiver with 8-ohm speakers? Shouldnt be a problem right?

10/15/2005 11:55:26 AM

esgargs
Suspended
97470 Posts
user info
edit post

Nope

Poor sound now.


Impedance matching is done for a reason.

10/15/2005 11:57:09 AM

sundance
All American
1001 Posts
user info
edit post

found out the receiver has a switch that lets it go back and forth between 6 and 8 ohms so all is good. thanks for the help.

10/15/2005 1:49:05 PM

davelen21
All American
4119 Posts
user info
edit post

so if you have an 8-ohm reciever and try to power 4 ohm speakers, the by product will be alot of heat that can damage your reciever. So if you don't listen to your speakers very loud and for short periods of time, there should be no problem, right?

10/16/2005 1:22:04 AM

Incognegro
Suspended
4172 Posts
user info
edit post

for shit like 6-ohm and 8-ohm... you have to understand that impedance is variable with respect to frequency and that 8-ohm is only a nominal rating... for most amps, a 20% difference in nominal impedance won't be a problem... it's when you start running 3.4ohm '4ohm' speakers on a 8ohm amp that you start encountering serious problems...


anecdotally I've ran a .9 ohm nominal configuration off of an amp rated for 4ohm and not had a problem yet, whereas I ran a 4ohm configuration off of an amp rated for 2 ohm and blew a fuse in it the first time I played it for any significant length of time at the higher end of its gain, so... again, anecdotally... ratings are shit if you are using something expensive, pad them... if you don't care about what you are using, disregard them entirely and let the fuses tell when you've gone too far ;p

10/16/2005 3:59:46 AM

 Message Boards » Tech Talk » Speaker question Page [1]  
go to top | |
Admin Options : move topic | lock topic

© 2024 by The Wolf Web - All Rights Reserved.
The material located at this site is not endorsed, sponsored or provided by or on behalf of North Carolina State University.
Powered by CrazyWeb v2.39 - our disclaimer.